Phones answered 24/7Albany, NY
Call (833) 490-5225
(833) 490-5225
Guide

Drying Old Brick and Plaster: How to Tell When a Wall Is Dry

How moisture meters behave on nineteenth-century brick and lime plaster in Troy and Albany, and how to tell a dry wall from one that only looks dry.

Illustration for the guide "Drying Old Brick and Plaster: How to Tell When a Wall Is Dry" (Albany, NY)
Short answer

A nineteenth-century wall is dry when readings at marked points match readings taken on the same material in an unaffected part of the same building, and hold that match for two consecutive days. There is no single number, because brick, lime plaster and lath each read differently from each other and from drywall.

Key takeaways

  • A dry standard is a reading taken on the same material elsewhere in the same building, not a figure from a manual.
  • The Central Troy Historic District, listed in 1986, holds nearly 700 properties from the early nineteenth to the mid-twentieth century, which is a great deal of solid masonry and lime plaster.
  • Pin meters measure between two points at a known depth; pinless meters read a shallow zone through the surface, and the two do not produce comparable numbers.
  • Salts left behind by evaporating water make masonry read wetter than it is, which is why efflorescence has to be read as a history rather than as a measurement.
  • Solid brick holds water deep in the wall and gives it up slowly, so a surface that feels dry on day three is routine and means very little.
  • Drying old plaster too aggressively cracks and delaminates it, so the target is a steady moderate humidity held for longer rather than the driest possible air.

Why does old masonry need a different approach?

Because it is a reservoir rather than a skin. A modern wall is a thin sheet of gypsum over a cavity, and it either is wet or is not. A solid brick wall with lime plaster on it is a thick, porous, absorbent mass that takes water in slowly, holds it through its full thickness, and releases it on its own schedule.

That changes the question from how fast can this be dried to how do we know it is dry. Water inside a brick wall moves toward whichever face has the drier air in front of it, and it arrives at the surface only as fast as the material allows. Put a strong air mover against that surface and you dry the outer few millimetres quickly, which feels like progress and tells you almost nothing about the eighty millimetres behind it.

The Capital Region has a lot of this construction. The Central Troy Historic District was listed on the National Register in 1986 and holds nearly 700 properties from the early nineteenth to the mid-twentieth century, taking in the Washington Park, Second Street, River Street, Grand Street and Fifth Avenue areas; the Fifth Avenue houses are modest two-story brick worker houses, and the Washington Park plans date to the 1830s. In Albany, the Center Square and Hudson-Park district runs from 1825 to 1932 and is about 80 percent attached brick rowhouses, and the Clinton Avenue district is roughly 92 percent nineteenth-century brick rowhouses.

What is a dry standard and why is it a reading rather than a number?

A dry standard is a measurement taken on the same material, in the same building, somewhere the water never reached. It is the baseline the wet areas are compared against. It is a reading rather than a published figure because two houses on the same street can have different masonry, different plaster mixes and different normal moisture content.

Taking one costs five minutes and is the step most often skipped. The crew that walks in, puts a meter on a wet wall and announces a percentage has produced a number with nothing to compare it to. The crew that reads the same wall in an upstairs bedroom first, writes that down, and only then reads the wet wall has created a target to dry toward and a way of proving when it has been met.

The standard also has to match the material. A reading from drywall in a 1960s extension is not a baseline for the lime plaster in the original front room, and a reading from a repointed section of wall is not a baseline for the original brick beside it. On a house of this age it is normal to end up with three or four dry standards, one per material, and every reading afterwards is read against its own.

Pin or pinless: which meter tells the truth?

Both, about different things. A pin meter measures electrical resistance between two probes driven to a chosen depth, so it reports on a specific point inside the material. A pinless meter reads a shallow field through the surface without marking it. On a thick old wall you need both, and you never compare one's numbers with the other's.

The pinless meter is the survey tool. Run it across a wall and it will show you where the wet area starts and stops, quickly and without leaving holes in historic plaster. What it will not do is see deep, and on solid masonry it is reading mostly the plaster and the first layer of brick. Used alone it produces the classic false result: the wall surveys dry while the core is still holding water.

The pin meter is the verification tool. Driven to depth at a marked point, it tells you what is happening inside, and repeated at the same point each day it tells you which direction the wall is moving. The cost is two small holes, which on a wall that is going to be replastered anyway is no cost at all. The discipline that makes either useful is marking the points, in pencil, and reading those same points every time.

How the materials in a pre-1900 Capital Region house behave while drying
MaterialWhat to expect
Solid brick, full thicknessTakes water in slowly, holds it deep, releases it over weeks; the slowest element on site
Lime plaster on wood lathSurface dries fast and misleads; the lath and the gap behind it stay wet longer
Wood lath and framingReads reliably with a pin meter; slow to dry and the element that decides when demolition is avoidable
Brick party wall between attached housesDries from both faces only if both households allow access; otherwise one side stalls
Modern drywall patch in an old roomReaches dry days ahead of everything around it and must not be used as the dry standard
Stone or rubble cellar wallOften damp as its normal condition, so the dry standard matters more here than anywhere

Why does a wall sometimes read wetter after it dries?

Salts. Water moving through masonry dissolves soluble salts and carries them to the surface, where it evaporates and leaves them behind. Those salts are conductive and hold atmospheric moisture, so a resistance meter reads them as water. The wall can be structurally dry and still produce a high number at that spot.

The visible version is efflorescence, the white powdery bloom on brick or plaster. Treat it as evidence that water has moved through this wall, which is useful, and not as a current measurement, which it is not. The reading to trust in that situation is a pin reading taken deeper than the salt layer, or a reading taken slightly to one side on clean material.

The same caution applies to anything else conductive in the wall: a metal lath repair, a nail line, foil-backed insulation added in the 1970s, a flue liner. All of them will throw a pinless meter. This is one of the practical reasons to use hidden water leak detection methods together rather than relying on one instrument, and to record what the point is as well as what it read.

How long should a brick wall take?

Longer than anyone wants, and the readings decide rather than the calendar. Modern materials in a dried room commonly reach their dry standard in days. A wet solid brick wall is usually still moving at the point where a drywall room would have been signed off, and a party wall between two attached houses is slower still.

What shortens it is not more power. It is removing the water that is still in liquid form, taking out the material that cannot dry and is feeding moisture back into the room, opening a path so the wall can evaporate from both faces where that is possible, and then holding the room at a sensible humidity continuously rather than in bursts. A machine switched off overnight gives the wall the night to re-equilibrate with damp air.

What lengthens it is an unaddressed source. A wall that keeps reading wet after a fortnight of competent drying is very often still being supplied: a failed gutter against the outside face, ground piled against the wall, a cracked downpipe, a slow leak in a buried pipe. Our guide to a rowhouse leak in Center Square covers the attached-house version of that search, where the source can be in a building you do not own.

Can a wall be dried too fast?

Yes, and old plaster is where it shows. Driving the surrounding air very dry very quickly pulls water out of the plaster surface faster than the body of it can supply, and the result is crazing, cracking along the lath lines, or a skim coat parting from the base coat. The damage is caused by the drying, not by the flood.

The management is unglamorous: a moderate humidity target held steadily, air moved across surfaces rather than blasted at one spot, and an eye on the room's humidity as well as the wall's readings. On a house with original lime plaster and decorative work it is reasonable to accept a slower schedule in exchange for keeping the plaster, and to say so in the drying plan so nobody later asks why the equipment was on for so long.

Heat needs the same care. Warming a room speeds evaporation, but applied hard to a cold masonry wall it can drive moisture deeper before it drives it out, and on painted plaster it lifts paint. The point of structural drying and dehumidification as a planned process, rather than as a pile of equipment, is exactly this balance between speed and the material surviving it.

What about cellars that were always damp?

A cellar under a nineteenth-century house often has a normal moisture level that would be alarming upstairs. Rubble or stone walls in contact with soil are rarely dry in any meaningful sense. The goal after a flood is to return that cellar to its own normal condition, which has to be established by reading an unaffected section.

This is the single clearest case for a dry standard, because without one there is no way to distinguish flood water from the condition the cellar has been in since it was built. Read a section of wall above the flood line and well away from it, read the floor in a corner the water did not reach, and write both down before any equipment goes in. Those two numbers are what finished looks like.

It also sets expectations honestly. A cellar that has always smelled of damp in August will still smell of damp in August after a successful drying, and a contractor who promises otherwise is selling a different job, usually a waterproofing one. Where the standing condition rather than the flood is the real complaint, the work belongs under basement and cellar moisture, and it is a separate conversation from the emergency.

What does the Hudson's flood record say about these houses?

That the oldest brick in Troy and Albany has been wet before. The National Weather Service office at Albany records the March 1913 Hudson flood at 29.7 feet at Troy and 21.45 feet at Albany, with March 1936 at 29.5 feet at Troy and 17.9 feet at Albany, and lists February 1857 as Albany's highest flood on record at 21.71 feet.

That history is one reason a reading on an old wall has to be interpreted rather than simply taken. Masonry that has been saturated and dried more than once carries salt deposits, old repairs, replaced brick, patched plaster and sometimes a damp-proofing attempt from a previous generation, all of which affect what a meter says. The wall's past is part of the measurement.

It is also a reason not to treat a modern reading as proof of a modern event. The February 1857 ice-jam flood and the 1913 and 1936 crests happened to buildings that are still standing and still occupied, and the water that soaked them is long gone. What matters today is the direction the readings move while drying is running, measured at the same marked points, against a dry standard from the same house. The flood history is context, not evidence about any one wall.

Frequently asked questions

Can I buy a moisture meter and check my own walls?

You can, and an inexpensive pinless meter is genuinely useful for finding where a wet area stops. Two cautions. First, take a reading somewhere the water never reached, on the same material, before you read anything wet, or your numbers mean nothing. Second, do not treat the percentage on the display as an absolute truth on masonry; it is calibrated for wood, and on brick or plaster it is a comparison tool rather than a measurement.

The plaster looks fine. Why does the wall still need drying?

Because on solid masonry the surface is the last thing to stay wet and the first thing to look dry. Water sits in the body of the brick and in the wood lath behind the plaster, neither of which you can see. A wall that surveys dry at the surface and reads wet at depth is the normal mid-drying condition of an old house, and stopping there is how a wall that was nearly saved ends up being replaced.

Do you have to drill holes in historic plaster?

Sometimes, and they are small. Where plaster is going to be replaced anyway, pin readings cost nothing. Where the plaster is original and worth keeping, readings can often be taken at an edge, behind a skirting, inside a closet or through an existing crack, and the survey work done with a pinless meter instead. Say at the start that the plaster matters to you; it changes where the points go, not whether the wall gets measured.

What if my neighbor will not let anyone into their side of the party wall?

Then the wall dries from one face only and it takes longer, which is worth knowing at the start rather than discovering in week three. In an attached brick house the party wall is a single mass of masonry shared by two households, and water in it belongs to both. Where access is refused, the realistic plan is more drying time on your side, readings that will fall more slowly, and a frank note in the log about why.

Is white powder on the brick a sign of mold?

Usually not. A white, crystalline, powdery bloom that brushes off dry is efflorescence, which is mineral salt carried to the surface by water and left there when it evaporated. Mold on masonry is more often gray, green or black, and it is fuzzy or staining rather than crystalline. Both tell you water has been present; only one is a biological problem, and if you are unsure the material rather than the color is what settles it.

When is it safe to replaster?

When the substrate behind the plaster has met its dry standard and held it, not when the room feels comfortable. New plaster over damp brick or damp lath traps the remaining water behind a fresh surface, and the bloom or the failure comes back through the new work within a season. The readings log is what tells you the date, and it is worth waiting the extra few days rather than redecorating twice.

Sources

  1. National Weather Service, Albany

This guide is general information for Albany County homeowners, not a substitute for an on-site inspection. Prices are estimates. See our disclaimer.

Need help today?

Call any hour and explain what is going on. You get a clear price before any work starts.

Keep reading

More guides

What moves a water damage restoration quote in Albany

A quote in Albany follows six things: how much floor area got wet, how far water wicked up the walls, how long it sat, how clean it was, which materials it soaked, and how hard the wet area is to reach.

WhatsApp